Technical FAQ
Specification, documentation, quotation process and commercial questions — answered as they stand today, including where the answer is that something has not yet been supplied.
General reference Product answers describe what this catalogue publishes today. Where a value has not been supplied, the answer says so rather than estimating it.
Questions and answers
Z5 denotes a 5-flute solid carbide end mill geometry — the number of cutting edges around the tool.
The product part number for that Z5 variant, abbreviated P/N. It is engraved on the tool and printed on the packaging, and it is the identifier to quote when requesting a quotation. It is the only identifier currently published for these variants: no SKU has been assigned and no barcode has been supplied. A part number is neither of those, and its digit count is not evidence of a barcode standard.
Because the manufacturer supplied one and not the other. The data sheet behind the Z5 series gives the coating, the ISO application range, the workpiece materials, their hardness bands and the full slot and side milling parameters — all of which are published, per variant. It says nothing about the substrate, the carbide grade, the helix angle or a coolant strategy, so none of those appears anywhere on this site. A published value that later turns out to be wrong is worse than an absent one, and an absent one is not improved by a guess standing next to real data.
Diameter, shank diameter, flute length (LOC), overall length (OAL), corner radius and flute count, for all ten Z5 variants. They are published on the series page and on each variant page, and an automated test compares the rendered pages against the catalogue on every build.
Not yet. No approved manufacturer drawing, CAD file or 3D model exists for these variants, and nothing is published in place of one — no generic schematic and no representative model. Published dimensions are in the specification table on each product page. If documentation is needed for your decision, request it with your quotation and it will be supplied when released. See Technical Downloads for the current document status.
No. No approved price list exists yet, so no price is published in any currency, and nothing is displayed as a placeholder value. Every tool is quoted on request. When approved price lists exist, pricing will appear per tool in USD and EUR, each from its own approved list — there is no currency conversion between them.
At three tiers — 10, 50 and 100 pieces. Each tier shows the total price for that quantity with the price per piece directly beneath it, so the effect of quantity is visible without arithmetic. Until approved prices exist, every tier resolves to a quotation instead of a price.
Agreed as part of a quotation — no fixed minimum order quantity is published while operational policy is being finalised.
Custom lengths can be discussed as part of an RFQ submission.
Special requirements — non-standard dimensions, specific geometry, a particular coating requirement, or a drawing to work from — are handled as part of a quotation request. Describe the application and the requirement in the enquiry; special requirements are recorded against the enquiry rather than resolved by substituting a nearby standard tool.
Yes. Volume and scheduled-delivery requirements are commercial terms established during quotation. Include the intended volume and the timeframe in the enquiry so the commercial response addresses them directly.
You receive a reference for the enquiry. The technical and commercial requirement is reviewed, a quotation or proforma invoice is prepared, and you review and approve it before anything proceeds. Payment instructions are provided at the appropriate stage, where applicable. The full sequence is set out on the quotation request page.
They are two separate lists and neither affects the other. The quotation request models an enquiry: unpriced, free-form, with quantities and notes you set. The Order Cart models a priced order and can only contain tools that carry an approved price. While no approved prices exist, the Order Cart cannot be filled and says so.
Enquiries are welcome from all international markets. Distribution coverage is expanding across key industrial markets in Europe and North America — see Global Distribution. Some markets are served through an appointed commercial route; where that applies, the enquiry is routed accordingly and you are told so directly at the point of enquiry.
Yes — a territory-based partnership rather than a drop-ship arrangement. Details and the application form are on the Distributors page.
Private-label supply is offered as a distinct commercial arrangement. See the Private Label page.
Because it is, and saying so is more useful than leaving gaps unexplained. Product families, technical resources and regional distribution information are being introduced progressively as each is confirmed. Everything already published is complete and browsable; see Platform Status for what is in preparation.
They are standard, publicly established machining engineering knowledge — formulas, ISO classifications and general industry practice. They are not EUROCUTPRECISION test data and contain no performance claim about any EUROCUTPRECISION tool. Every guide states this at the top and lists the conditions that determine the values on your job.